| About the Author:
| |
Heinz Bloch
is a registered consulting engineer with offices in Montgomery, Texas.
Mr. Bloch is a graduate from the New Jersey Institute of Technology with B.S. and M.S degrees.
He has been elected to three National Honor Societies, and is a member of the Vibration Institute, and the
ASME. |
| Before retiring from Exxon in 1986 after twenty-four years of service, Mr. Bloch's professional career included long-term assignments as Exxon Chemical Company's Regional Machinery Specialist for the United States.
He also held machinery-oriented staff and line positions with Exxon affiliates in the United States, Italy, Spain, England, The Netherlands and Japan. |
| |
Contents of the Reference Guide |
| Foreword | |
Acknowledgments |
| Part 1: Background to Process Machinery Maintenance Programming |
| 1 Machinery Maintenance: An Overview |
| 2 Maintenance Organization and Control for Multi-Plant Corporations |
| 3 Machinery Foundations and Grouting | |
4 Process Machinery Piping |
| Part II: Alignment and Balancing | |
5 Machinery Alignment | |
6 Balancing of Machinery Components |
| Part III: Maintenance and Repair of Machinery Components | |
7 Ball Bearing Maintenance and Replacement |
| 8 Repair and Maintenance of Mechanical Seals and Rotating Equipment Components | |
9 Centrifugal Compressor Rotor Repair |
| 10 Protecting Machinery Parts Against Loss of Surface |
|
| Machinery Component Maintenance and Repair Series |
|
 |
This 12-part videotape reference
library presents guidelines, procedures, and techniques that the author has
collected and field tested over the past several decades.
Each module provides a long needed source
of practical engineering reference information that the viewer can easily adapt
to similar machinery or machinery installations in a particular plant.
This videotape lecture series features
Heinz Bloch.
Also included with the series is a 600-page
reference text that expands on many of the topics presented in the videotapes. | | |
|
$2495.00 (12 video series) |
|
Machinery Component Maintenance and Repair Series -
$2495.00 each |
 |
| These videos can also be purchased separately as shown: |
|
|
Part One: Introduction and Overview.
35 minutes. Order BN11, $225.00 | | |
Part Two: Machinery Foundations and Grouting.
31 minutes. Order BN12, $225.00 | |
|
Part Three: Machinery Piping Considerations.
25 minutes. Order BN13, $225.00 | | |
Part Four: Machinery Alignment Methods.
40 minutes. Order BN14, $225.00 | | |
Part Five: Balancing Machinery Components.
18 minutes. Order BN15, $225.00 | | |
Part Six: Ball Bearing Maintenance and Replacement.
37 minutes. Order BN16, $225.00 | | |
Part Seven: Mechanical Seal Installation, Repair, and Maintenance.
53 minutes. Order BN17, $225.00 | | |
Part Eight: Welded Shaft Repair Methods.
37 minutes. Order BN18, $225.00
| | |
Part Nine: Casting Salvaging Methods and Compressor Rotor Design Overview, Disassembly, and Cleaning.
55 minutes. Order BN19, $225.00
| | |
Part Ten: Compressor Rotor Repair, Reassembly and Verification.
50 minutes. Order BN20, $225.00 | | |
Part Eleven: Hydraulically Fitted Coupling Hubs / Selection and Application of O-rings.
20 minutes. Order BN21, $225.00 | | |
Part Twelve: Protecting Machinery Parts Against Loss of Surface.
34 minutes. Order BN22, $225.00 | | |
Additional Text: Order 1781,
(Reference Guide comes with Series Purchase Only)
$99.95 | |
 | | | |
|
|